# Frequent question: How high should a forklift load be carried?

Contents

Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.

## How high should a load be on a forklift?

Lower the load so that its lowest point is 15 to 20 cm (6 to 8 inches) from the floor. While traveling, keep the load at a safe travel height.

## How high should a load be carried on a forklift OSHA?

Keep the center of gravity of the load as low to the ground and as close to the front wheels as possible: Carry the load at the lowest position possible, 4 to 6 inches from the ground. Tilt the mast back and position the heaviest part of the load against the carriage.

THIS IS INTERESTING:  How much does a small forklift weigh?

## How high should a load be carried on a smooth surface?

Once the load is lifted, lower it to a safe traveling height. Keep the forks two to four inches off the floor if driving on a smooth surface.

## When traveling with a load How high should the load be lifted?

allow 2 to 3 inches of clearance at the sides and back of the load; move the load slowly into position; tilt the load forward, then lower it; level the forks so they are no longer tilted; and.

## When setting a load What should you do first?

When setting a load, what should you do first?

Place the tasks for lifting a loaf in their proper order.

1. Level the forks and set the forks for proper width.
2. Position the load on the forks.
3. Lift the load straight up.
4. Tilt the load back slightly.
5. Back up.

## What should you not do when a load is elevated?

Operating Safely

Never raise a load or turn on an uneven surface. In such cases, your center of gravity will quickly move outside of the stability triangle. While traveling empty on a ramp, your forks should always point downhill.

## How should you travel up a slope with a loaded forklift?

Requirements and Recommended Practices

1. When traveling with a load, the load should point up the incline, regardless of direction of travel.
2. Going up the incline: Drive forward. Forks pointed upgrade. Use a spotter if load blocks the driver’s view.
3. Going down the incline: Drive in reverse. Turn head and face downgrade.

## How do you calculate the load capacity of a forklift?

You can determine the Maximum Load Moment for any forklift by multiplying the weight rating by the center load distance state on the data plate. In the example we used above, it would be a 5,000 lb capacity multiplied by a 24 inch load center (5,000 x 24), which gives you a Maximum Load Moment of 120,000 inch pounds.

THIS IS INTERESTING:  How do you control a scissor lift?

## Should a load be strapped to a forklift?

All loads should be made stable by either interlocking the objects, or strapping or shrink-wrapping the load, to prevent individual objects from falling off the pallet. Long loads, such as carpet rolls, reduce the stability of a lift truck.

## What should you never do when carrying a load on forklifts?

Forklift operators should never:

1. Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable. …
2. Allow anyone to stand underneath or right next to raised forks. …
3. Carry a load with only one fork as it stresses the carriage.

## What should you do if forklift is tipping over?

In a forklift tip over, you should:

1. remain seated and don’t lean out of the forklift.
2. brace your feet, hold tight and lean away from the point of impact.

## What should you check before lifting a load?

Check out these safe lifting and handling tips, recommended by the Health and Safety Executive.

1. Think before you lift. …
2. Keep the load close to the waist. …
3. Adopt a stable position. …
4. Ensure a good hold on the load. …
5. Do not bend your back when lifting. …
6. Do not bend the back any further while lifting. …
7. Do not twist when you lift.

## What should you check before lifting a load with a forklift?

When using a forklift, workers should begin by performing basic safety checks on the components of the forklift, including the fluids, tyres, controls, warning devices, seating, brakes and mast forks.

## How should the rated capacity of a forklift be determined by you?

As a general rule, load center is 24″ from the face of the forks (the center point of standard 48” x 48” pallet). Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs. You can find the rated capacity of a forklift on its data plate.

THIS IS INTERESTING:  How much fuel does a forklift use?