Do and don’ts for forklift?
The 5 Dos and Don’ts of Forklift Safety
- Do Drive Responsibly. Just like driving a car on the road, you should always operate your forklift at a speed that will allow you to stop safely. …
- Don’t Go Over Your Forklift’s Load Capacity. …
- Do Be Aware of Pedestrians. …
- Don’t Skimp on Training. …
- Do Maintain Your Forklift.
What should you not do when a load is elevated?
Never raise a load or turn on an uneven surface. In such cases, your center of gravity will quickly move outside of the stability triangle. While traveling empty on a ramp, your forks should always point downhill.
What should you do before lifting a load forklift?
Lifting the Load
- Ensure there is adequate overhead clearance before lifting a load.
- Slowly lift a load and tilt the mast backward to stabilize it.
- Slowly return the lift control to the neutral position.
What are the OSHA regulations for forklift?
OSHA 29 CFR 1910.178(I) requires that employers provide forklift operators training for vehicle inspection and maintenance. Operators must be over 18 years of age and be recertified at least once every three years. The similar CSA standard is B335-04 (R2012).
What is forklift safety?
Forklift safety refers to the safe management of operations of forklifts for protecting operators and other employees working in the vicinity. This is done by following standard operation procedures, minimizing hazards, risks and accidents directly or indirectly related to forklift operations.
How do you carry a load on a forklift?
Carrying the load
Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
What is the safest position for your forklift when you are carrying a load up a ramp onto a trailer?
When traveling with a load, the load should point up the incline, regardless of direction of travel. Going up the incline: Drive forward. Forks pointed upgrade.
What safety steps should you take before transporting a load?
- Avoid bumps, uneven surfaces and slippery routes while loading and transporting goods.
- Look out for loose ground objects as they could cause the load to move around or lose control over the equipment.
- Alert your colleagues and pedestrians by using the horn when you turn around a corner to avoid a collision.
How do you ensure the load is stable?
Check for any overhead objects before lifting or stacking loads. Do not lift or move loads that are not safe or stable. Make sure loads are correctly stacked and positioned across both forks. Make sure the load is evenly balance across both forks.
What is the correct behavior when driving a loaded forklift up an incline?
When going up an incline with a load, a forklift operator should: Keep the forks pointed upgrade. Move the lift forward slowly and carefully. Ask for assistance from a spotter; a spotter can help an operator keep an eye out for hazards that block their view.
What is the first thing you need to do before raising or lowering a load?
Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.
What are some safety rules for a warehouse?
10 Warehouse Safety Tips
- Ensure Safety Equipment is Always Used. …
- Eliminate Potential Safety Hazards. …
- Identify and Mark Hazardous Zones Clearly. …
- Provide Proper Training and Courses. …
- Proper Clothing Should be Worn. …
- Promote Awareness. …
- Shelving Safety. …
- Vehicle Safety.
What should you do if forklift tips over?
If the forklift is tipping over, protect yourself by staying put:
- Stay in your seat and do not attempt to jump off.
- Lean away from the falling direction of the lift.
- Hold onto the steering wheel and make sure you’re stable.
What is the load center of a forklift?
According to OSHA, “The load center is the distance from the face of the forks to the load’s center of gravity.” It is important for operators and managers to understand the forklift load’s center of gravity in order to operate and transport loads safely in their operations.